Cutting/Fabric    Machines    Services    Clients    Home       

          

 

GREAT USED MACHINES - CALL TODAY!

We take used equipment in trade on our new systems, and have built up a nice inventory of used laser cutters, laser heads, power supplies, and various other used parts. The following is a partial list of what we currently have in inventory. Our stock changes daily, so call if you don’t see what you are looking for.

Used Machines:

Proel (Ricamar) 50 watt CO2 water cooled, 38" x 50" cutting area (Refurbished)* - GREAT DEAL

This machine comes with the computer and software installed. Just plug it in. It needs to be vented to the outside, it basically has a dryer vent hose on it now. The water cooler is built into the cabinet, as well as the water recirculation. The machine may need an alignment when it arrives, but I don't think it will. The warranty is six months parts, and no labor warranty. No warranty on optics, or the computer. It is a used machine, we have been through the machine and replaced or repaired any items needing attention.  We have replaced all of the electronics and upgraded them to our latest control system and motors. It was taken in trade on a new flat bed. The customer told us that it had been used very little. In fact when I first looked at it, the machine was pushed over in a corner and covered up.

CCT Zeus 25 watt CO2 water cooled, 38" x Roll Feed - AFFORDABLE

This machine was taken in trade on a new machine. It has about six years of use on it. The laser was rebuilt a few years back, and the machine has had a complete rebuild. All bearings and shafts were replaced during the rebuild. All optics are good, and all of the belts are in good condition. The water chiller has been cleaned, and serviced.

We have checked the machine out thoroughly, and run it in our production for a couple of weeks. We will give a six month warranty on parts, no labor warranty, or optics warranty. We can install the machine if you need us too.

Edgewise RFL48 25watt CO2 air cooled 48" x Roll Feed - BEST DEAL

This machine was bought from a bank a few years ago. We have run it in our production for several years. It is a good machine with full manual control of power and speed. It accepts a HPGL file. We set up a cad program to output to a HP plotter, and the machine worked well. It has a air cooled Synrad 25 watt laser. We have run 50yd rolls of fabric off the back of this machine for days at a time. The machine had almost no time on it when we bought it, The only use has been from our production.

Gamata 50watt CO2 air cooled 48" x 60" cutting area (Refurbished)* - WORK HORSE

This is a very unusual machine. It is a very well built Flat Bed laser cutter. We are currently refitting this machine with our new motion control system, and a 50 watt Universal air cooled laser. This makes this machine every bit as good as one of our new machines, with the new software, and laser controls. The only exception is the older chassis. The machine has a honeycomb bed, and a 48" x 60" cutting area. This is a excellent bargain for someone looking for current technology and sharp price. The laser can be changed from 10 watt to 200 watt in this chassis.

Epilog  25watt CO2 air cooled 16" x 22" cutting area - GREAT STARTER

This was a used machine we took in trade. We know longer sell these machines. It has been used for a few production jobs, and done some sample cutting. It has a 25 watt Synrad air cooled laser. It can be modified to a 30 watt laser for additional cost.

 

Thor Series TH60100 CO2 100 Watt Air Cooled Laser 36" x 60" cutting area - Powerful Large Machine

This is a used 100 watt machine that we took in trade. It has a air cooled 100 watt CO2 Laser that is making 142 watts. The machine has about fourteen hours of use on it. It comes with the honey comb and plate beds. It has our latest control system and motors in it. It has full Raster, and Engraving functions. It will read .dxf, .ai, .dst, .plt, .bmp, and .jpeg files. The machine comes with a full six month warranty on parts, and a 30 day labor warranty. It includes the extraction blower, air pump, and all necessary items to get the machine up and running.

 

 

Thor Series TH6050 CO2 30 Watt Air Cooled Laser 36" x 60" cutting area - Large Cutting Area

This is a new 30 watt machine that we took in trade. The customer decided he needed one of our Drawer Machines. It has a air cooled 30 watt CO2 Laser that is making 42 watts. The machine has zero (0) hours on it. (It was shipped, but never installed) It comes with the honey comb and  bed plates. It has our latest control system and motors in it. It has full Raster, and Engraving functions. It will read .dxf, .ai, .dst, .plt, .bmp, and .jpeg files. The machine comes with a full six month warranty on parts, and a 30 day labor warranty. It includes the extraction blower, air pump, and all necessary items to get the machine up and running.

 

 

 

New & Used Laser tubes:

25 watt Synrad CO2 (USED) $2195.00

25 watt Synrad CO2 (Refurbished) $3245.00

10 watt Synrad CO2 (USED) $1510.00

50 watt Universal CO2 (USED) $5535.00

60 watt Glass CO2 (New) $875.00

 

Power Supplies, Motors, Etc.

30 volt 20 amp Supplies New (Synrad) $965.00

48 volt 30 amp Supply New (Universal) $1240.00

Zeus used motor x or y axis $258.00

Refit kit for Zeus motors (New Motor, and Harness) $695.00

Optics 1" mirrors (New Style Coating) $275.00

We also stock bearings, rails, optics, belts, motors, keypads, and hardware for most machines.

Call if you have a specific request. If we don’t have it we can probably make it, with your part as a sample.

Contact ILS for more information.

sales@integratedlasers.com

Phone:  (706) 857-5153

Fax:  (706) 857-5167

 

170 Laser Lane

Summerville, GA 30747

 

Contact our National Sales Representative Phil Lehman at 434-242-9322

 

[Cutting/Fabric]   [Machines]   [Services]   [Clients]   [ILS Home]

Send mail to webmaster@integratedlasers.com with questions or comments about this web site.
Copyright © 2009 Integrated Laser Systems, Inc.