GREAT USED MACHINES - CALL TODAY!
We take used equipment in trade on our new systems, and have built up a nice inventory of used laser cutters, laser heads, power supplies, and various other used parts. The following is a partial list of what we currently have in inventory. Our stock changes daily, so call if you don’t see what you are looking for.
Used Machines:
-
Proel (Ricamar) 25 watt CO2 water cooled, 38" x 18" cutting area -
This machine comes with a computer with software installed. Just plug it all in. It needs to be vented to the outside, it basically has a dryer vent hose on it now. The exhaust blower is built into the cabinet, as well as the water recirculation. The machine may need an alignment when it arrives, but I don't think it will. The warranty is 30 days parts, no labor warranty. No warranty on optics, or the computer. We have run the machine in the last week so it is in good shape. It is a used machine, we have done no repairs to it. It was taken in trade on a new flat bed. The customer told us that it had been used very little. In fact when I first looked at it, the machine was pushed over in a corner and covered up.
-
CCT Zeus 25 watt CO2 water cooled, 38" x Roll Feed -
This machine was taken in trade on a new machine. It has about six years of use on it. The laser was rebuilt a few years back, and the machine had a complete rebuild two years ago. All bearings and shafts were replaced during the rebuild. All optics are good, and all of the belts are in good condition. The water chiller has been cleaned, and serviced.
We have checked the machine out thoroughly, and run it in our production for a couple of weeks. We will give a 30 days warranty on parts, no labor warranty, or optics warranty. We can install the machine if you need us too.
-
CCT Zeus 25 watt CO2 water cooled 38" x Roll Feed (Refurbished)* - SATISFIED CUSTOMER
The warranty is 30 days parts, no labor warranty. No warranty on optics.
-
Edgewise RFL48 25watt CO2 air cooled 48" x Roll Feed -
This machine was bought from a bank a few years ago. We have run it in our production for several years. It is a good machine with full manual control of power and speed. It accepts a HPGL file. We set up a cad program to output to a HP plotter, and the machine worked well. It has a air cooled Synrad 25 watt laser. We have run 50yd rolls of fabric off the back of this machine for days at a time. The machine had almost no time on it when we bought it, The only use has been from our production.
-
Gamata 50watt CO2 air cooled 48" x 60" cutting area (Refurbished)* -
This is a very unusual machine. It is a very well built Flat Bed laser cutter. We are currently refitting this machine with our new motion control system, and a 50 watt Universal air cooled laser. This makes this machine every bit as good as one of our new machines, with the new software, and laser controls. The only exception is the older chassis. The machine has a honeycomb bed, and a 48" x 60" cutting area. This is a excellent bargain for someone looking for current technology and sharp price. The laser can be changed from 10 watt to 200 watt in this chassis.
-
CCT FB400 10watt CO2 air cooled 18" x 24" cutting area -
This was a demo machine we have had for a few years. We know longer sell these machines. It has been used at a few trade shows, and done some sample cutting. It has a 10 watt Synrad air cooled laser. It can be modified to a 30 watt laser for additional cost.
Used Lasers:
-
25 watt Synrad CO2 (USED) $2195.00
-
25 watt Synrad CO2 (Refurbished) $3245.00
-
10 watt Synrad CO2 (USED) $1510.00
-
50 watt Universal CO2 (USED) $5535.00
-
75 watt Glass CO2 Lost Gas (USED) $1268.00
Power Supplies, Motors, Etc.
-
30 volt 20 amp Supplies New (Synrad) $965.00
-
48 volt 30 amp Supply New (Universal) $1240.00
-
Zeus used motor x or y axis $258.00
-
Refit kit for Zeus motors (New Motor, and Harness) $695.00
-
Optics 1" mirrors (New Style Coating) $225.00
We also stock bearings, rails, optics, belts, motors, keypads, and hardware for most machines.
Call if you have a specific request. If we don’t have it we can probably make it, with your part as a sample.